Browse all practice questions for the Senior Sewage Treatment Worker Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Senior Sewage Treatment Worker Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is the volume of water in gallons contained in a cubic foot?
  • What is the primary hazard associated with storing batteries while being charged?
  • What is a common indicator of water quality in sewage treatment plants?
  • Which term is used to express the rating of a storage battery?
  • What type of lubricating grease should be used on pump ball bearings exposed to water washing?
  • Consumption of electrical energy is registered on which device?
  • How are sludge tanks typically heated?
  • Material removed from sewage by the fine screen is most frequently:
  • A metal washer is MOST often used with which type of screw?
  • What device is typically used to control the flow of sewage into a treatment plant?
  • Among common obstructions in sewer lines, which occurs most frequently?
  • What is a device with an edge or notch used for measuring liquid flow called?
  • What is considered a sign of a potential gas leak in sewage treatment facilities?
  • Why is painting metal equipment in a sewage plant important?
  • What does the abbreviation I.P.S. stand for in relation to pipes?
  • Why should water NOT be used to extinguish fires near electrical apparatus?
  • Ordinary soft solder is primarily a mixture of which two metals?
  • Which process in sludge treatment reduces the volume of sludge sent to the digester?
  • Who was the immediate superior of the sewage treatment worker?
  • What happens to most digested sludge in the city sewage system?
  • If a car travels at a constant speed of 36 miles per hour, what is its speed in feet per second (one mile equals 5,280 feet)?
  • What is the primary reason for mixing a thinner into paint?
  • A rasp is classified as which type of tool?
  • Which conditions should sewage treatment workers avoid when working near electrical equipment?
  • Which tool is usually used to drive a lag screw?
  • How many cubic feet of concrete are in a slab that is 5 feet wide, 6 feet long, and 6 inches deep?
  • How does explaining departmental procedures to workers impact their interest?
  • At what exact time was the victim found?
  • Which type of wrench is the best choice for a large square nut?
  • Which temperature range is considered the most efficient for sludge?
  • At what rate is air applied in a conventional activated sludge treatment plant?
  • What is the circumference of a circle with a diameter of 10 inches, MOST NEARLY?
  • On a 1" bolt with 10 threads per inch, how far does the nut move after being turned 6 complete turns?
  • What is the appropriate first aid for a conscious person suffering from chlorine inhalation?
  • If a supervisor notices a crew member skipped routine maintenance, what should the supervisor do first?
  • What was the name of the patrolman involved in the incident?
  • What is the primary reason for putting orders in writing?
  • Which is an essential consideration in the design of a sewage treatment facility?
  • Which type of pump is most commonly used for pumping sewage?
  • Frothing in sewage treatment is most frequently attributed to which factor?
  • Which component is crucial for preventing spills and backups in sewage systems?
  • The difference between a stud and a bolt is that the stud has:
  • How should a supervisor handle a crew member who complains about favoritism in work assignments?
  • When should artificial respiration be performed on a victim?
  • What is the electrolyte used in an ordinary flashlight-type dry cell?
  • On what day did the incident occur?
  • A set screw is often used to:
  • What is the advantage of using brass liners in a bench vise?
  • How can a supervisor best assess the effectiveness of safety training for workers?
  • The use of a cold chisel with a mushroomed head is:
  • After a discussion with a crew member where you have disproved his complaint, what is the best course of action?
  • How can moisture content in sludge be reduced effectively?
  • A column of water with a height of 4.6 feet at sea level will exert a pressure of MOST NEARLY how many pounds per square inch?
  • What is the estimated total cost of the water pollution program initiated in 1996?
  • An oilstone is typically made of which material?
  • What is a significant benefit of a supervisor introducing a new worker to the team and providing information about the workplace?
  • Which of the following saws is best suited for cutting wood along the grain?
  • For pumping against a very high head, which type of pump is the best choice?
  • Which tool is often used alongside a square shank screwdriver?
  • What commonly occurs to stop small leaks in steel or wrought iron water pipes?
  • What method is primarily used for the removal of suspended solids from sewage?
  • What is the most similar meaning of the word maximum as per the article?
  • By 2030, how many gallons is the city expected to treat daily?
  • Which method is used to prime a centrifugal pump?
  • What is the volume in cubic feet of a coal bin measuring 8 ft long, 5 ft wide, and 7 ft high?
  • What is the benefit of using pipe joint compound when making up a screwed joint?
  • How can the hazards of electric shock be reduced when operating a portable electric tool in a damp location?
  • Which type of wrench is specifically designed for tightening pipe fittings?
  • What is the main goal of sewage treatment?
  • What is an example of a proper safety measure when sharpening tools?
  • Why should electric hand tools not be lifted by their service cords?
  • What is the primary function of a grit chamber in a sewage treatment plant?
  • What is the total length of pipes measuring 22 1/8", 7 3/4", 19 7/16", and 43 5/8"?
  • How many days will it take for 4 men to complete a job that 6 men can complete in 8 days, assuming equal work rate?
  • Who held the position of Stationary Engineer Electric?
  • What is the distance in inches between the ends of a 6-inch horizontal line and an 8-inch vertical line drawn at right angles?
  • In which stage of sewage treatment are floating materials, like grease, typically removed?
  • What is the square root of 64?
  • What does the word "discharged" mean in the context of the article?
  • What material are soft jaw inserts commonly made of to protect metal surfaces in a vise?
  • Which description matches a board that contains exactly 10 board feet?
  • What is the primary purpose of the sluice gate in sewage treatment?
  • What tool is used to remove burrs from the end of a 1/2" diameter steel pipe after cutting?
  • What does the abbreviation BOD stand for?
  • What is the primary cause of water hammer in a sewage system?
  • When sludge is withdrawn from a sludge gas collector tank, what must be added to prevent the development of negative pressure?
  • What should be done immediately if a co-worker is unconscious and not breathing after an electric shock?
  • In water supply systems, small leaks are often filled over time with which substance?
  • What type of oil is best used for cutting threads on steel pipe?
  • What is the main reason for defective operation in an aeration tank?
  • What tool is best suited for drawing a circle?
  • What happens to the amount of dissolved oxygen in waterways due to pollution?
  • What type of pipe fitting allows for four openings to connect a line at right angles?
  • Among the listed abrasives, which is the least coarse?
  • Which piece of equipment is operated in conjunction with air pressure?
  • When might it be necessary to replace the ballast in a fluorescent light?
  • If smoke is seen coming from an electric control device, what is the first action to take?
  • What is the primary method for odor control in sewage treatment plants?
  • The type of pump most frequently used to pump thickened sludge is the ___________ type:
  • What property describes a metal that can be rolled into thin sheets?
  • In a digester tank with a floating or rising cover, it is made airtight by means of a(n):
  • To ensure safety, what is the maximum distance from the wall to the foot of a 12-foot ladder?
  • When using a 15-foot ladder secured against a wall, how far can a person safely reach out to one side?
  • What is an effective way to communicate safety expectations to a sewage treatment crew?
  • If a car travels 60 miles per hour, how far does it travel in 2.5 hours?
  • What is the best type of fire extinguisher to use on a fire caused by a shorted air-conditioning unit?
  • In aeration tanks, what role does sludge play in the treatment process?
  • What is the purpose of a venturi in a sewage treatment plant?
  • What immediate response should be taken if someone has been exposed to a chemical spill in their eyes?
  • What is the electrolyte commonly found in an ordinary storage battery?
  • What is the primary function of a trap under a plumbing fixture?
  • Which factor primarily affects the efficiency of the activated sludge process?
  • Which of the following methods can enhance the efficiency of sewage treatment?
  • What does the term pollution most nearly mean?
  • What is a common cause of pump failure related to water flow?
  • How long should a freshly poured concrete surface exposed to air be cured?
  • What is the best approach for a supervisor to take with an older, slower worker who is otherwise reliable?
  • What type of wrench is used for tightening a round nut with notches?
  • What is a necessary quality for records in a sewage treatment plant to support future changes or expansions?
  • Which of the following is considered a potential byproduct of sewage treatment?
  • What is the main reason for disinfecting treated sewage before discharge?
  • In the provided context, the word "offensive" most nearly means what?
  • What term describes the ratio of weight of a substance to the weight of an equal volume of water?
  • What is a significant consequence of excessive grease buildup in sewage systems?
  • The term "categories" in the given context most nearly refers to what?
  • What is the main reason for grounding electrical equipment and circuits?
  • Approximately how many minutes elapsed between the start of the sewage treatment worker's inspection and the ambulance's arrival?
  • What is the best course of action if a 15-ampere fuse blows and continues to blow after replacing it?
  • What is the best method for detecting chlorine leaks?
  • After witnessing an acid splash into a fellow worker's eyes, what should you do first?
  • Where should oily waste rags be stored when not in use?
  • What is the usual method for adding chlorine to sewage?
  • What is considered the most important skill in successful leadership?
  • What is the process called when sludge digestion occurs without the presence of free oxygen?
  • What is the main reason for lubricating machinery?
  • What device is most frequently used to prevent an electric motor from being overloaded?
  • When someone is in shock, what should be prioritized in their treatment?
  • What role does a centrifuge play in sewage treatment?
  • A U-tube manometer is principally used to measure what?
  • After brass or black iron pipe has been cut, it should be:
  • What is the best basis for setting up a maintenance program for new equipment?
  • Which tool is most likely used for sharpening a chisel?
  • What is the purpose of sludge digestion in sewage treatment?
  • A bar screen serves the same purpose as a:
  • What factor primarily determines the sizing of sewage treatment tanks?
  • Which of the following items has the lowest viscosity?
  • What are the wooden planks used to scrape sludge from the bottom of a tank called?
  • Which fastener is the best choice for attaching a pipe support bracket to a concrete wall?
  • What device prevents overheating in an electric motor?
  • What is usually necessary to properly ground portable electric hand tools?
  • How often is it recommended to lubricate machinery?
  • What is the weight, in pounds, of one cubic foot of fresh water?
  • What should a supervisor prioritize to ensure the safety of their workers?
  • To control the flow of liquid to a delicate gauge, which type of valve should you use?
  • What is the size of the smallest graduation on a 6-foot folding rule typically?
  • If a pump could produce a perfect vacuum, what is the MAXIMUM height it could lift water at sea level, in feet?
  • A pump can fill a 15,000 gallon tank in 2 hours and 30 minutes. How long will it take to fill a 60,000 gallon tank at the same rate?
  • How are grease and fats typically removed from sewage?
  • In which type of plant does flocculation most frequently occur?
  • What is the function of grit chambers in sewage treatment plants?
  • What defines a safe edge in a specific application?
  • Which disease can result from drinking water polluted by sewage?
  • Why is it important to know the location of pressure points when treating someone?
  • If a centrifugal pump is not delivering the expected sewage flow, which of the following is NOT a potential cause?
  • What is the first action you should take if a crew member falls down a flight of stairs and injures his leg?
  • What is the appropriate tool to use for removing burrs from inside a pipe?
  • The one of the following that is used to change the speed of certain types of electric motors is a(n):
  • What is the optimum pH value of sludge in a digester?
  • What specific property characterizes a malleable metal?
  • What is the function of a starter in a fluorescent light fixture?
  • When training a new worker to operate equipment, what is the first step?
  • What would be a poor choice for a supervisor regarding their own responsibilities?
  • If a crew member presents a suggestion that you believe will not work, what is your best response?
  • Which element in sewage treatment is primarily responsible for breaking down organic matter?
  • What is the safest way to carry a power tool?
  • Aside from the bulb, which part of a fluorescent light requires frequent replacement?
  • When using a needle valve, what is its primary function?
  • What is the most nearly sewage detention time in an aeration tank using modified aeration?
  • Which material should fittings be made of when used with copper pipes?
  • Which type of waste is typically treated in a sewage treatment plant?
  • Which of the following devices is considered a primary treatment device for sewage?
  • Compressed air can be used to clean generator and motor windings provided the air is:
  • What is the best method for cleaning a dirty commutator?
  • In the Modified Aeration process, what is the most nearly percentage of returned sludge to the aeration tank?
  • Which metal is most commonly used for outboard bearings?
  • What is the area in square feet of a floor measuring 42 feet wide and 75 feet long?
  • What is the purpose of wearing safety goggles while operating a drill press?
  • When sharpening a tool on a grindstone, why is the tool often dipped in water?
  • If one third of a 19-foot length of lumber is cut off, what will the length of the remaining piece measure approximately?
  • Which parameter is most critical in assessing the performance of a sewage treatment system?
  • What is the unit of electrical capacitance?
  • Which type of sewage treatment is primarily focused on biological processes?
  • What tool is commonly used to cut off the head of a rivet?
  • To protect current and future beaches, how much additional funding must the city allocate?
  • What does it indicate if crew members ask questions about a new procedure being introduced?
  • What is crucial for ladder stability according to safety rules?
  • What is the BTU per cubic foot value of sludge gas from a well-established digestion tank?
  • What does the word evident mean as used in the article?
  • A plant is designated as an Activated Sludge Plant when:
  • What valuable gas is produced as a byproduct of sewage treatment?
  • What is the best way for a supervisor to address a crew member who has not completed a task?
  • How many gallons of water can a tank measuring 3 feet by 2 feet by 2 feet hold?
  • What is the purpose of brass liners over the jaws of a bench vise?
  • What is the name of the sewage treatment worker?
  • Which characteristic best describes activated sludge?
  • To increase the delivery volume of a reciprocating pump, what modification is typically made?
  • When addressing safety hazards, what is paramount for a sewage treatment worker?
  • How do settling tanks operate effectively?
  • What monitoring parameter is essential in evaluating the performance of a sewage treatment plant?
  • What should a supervisor do if a crew member consistently misses deadlines?
  • What does "rodding" a sewer pipe most likely refer to?
  • What is the method of removing floating grease or scum from the surface of sewage in a tank called?
  • Which step is taken to prevent or control sludge bulking in the Activated Sludge Process?
  • What type of portable fire extinguisher is most effective for fires involving live electrical equipment?
  • Which device is normally used to control the flow of sewage to the treatment plant from the intercepting sewer?
  • Why is a leak in a chlorine tank particularly hazardous?
  • Which oil is recommended for the gearbox of a 20-ton sewage plant crane?
  • Which type of wrench is best suited for tightening a nut with a limited swing length?
  • Before starting a newly installed pump, what should you do first?
  • If you discover an unconscious person across a live electric wire, what should your first action be?
  • What is the main function of a check valve in a pipeline?
  • Which type of valve allows water to flow in one direction only?
  • What is the sum of 3 5/8 + 4 1/4 + 6 1/2 + 7 1/8?
  • What is the most frequent cause of noisy operation in a motor?
  • What is a fastener that has threads at both ends called?
  • Why are punch marks placed on machinery parts during repair?
  • What is the primary purpose of a center punch?
  • Which sludge gas encountered at sewage treatment plants is corrosive and damaging to metals?
  • Upon discovering a mistake in a crew's job, what should a supervisor prioritize?
  • If a concrete mix is formulated as 1:2:4, how is it composed?
  • What process is used to control odors in sewage systems?
  • The one of the following that is used to connect two pipes together in a straight line is a:
  • How many new plants will the city add according to the article?
  • What is the primary purpose of an electrical transformer?
  • What method yields the quickest results when starting a digester unit?
  • What is a common defect of a chisel?
  • A wet undigested sludge with a large amount of grease will most likely?
  • Which type of wrench is commonly used for tight spaces and difficult angles?
  • What is the function of a circuit breaker similar to?
  • A spanner wrench is specifically designed for which purpose?
  • Which statement is most nearly correct regarding lubrication?
  • What is the most effective tool for cleaning files?
  • If five dry cells are connected in series, what will the terminal voltage be in relation to one cell?
  • Which type of motor is most commonly used with an AC or DC source of supply?
  • What is the primary reason for enclosing electrical switches and current-carrying components?
  • What is the primary reason reprimanding a crew member in public is considered a bad practice?
  • In hydraulic systems, what is the common purpose of lard oil?
  • What is the impact of a clogged suction line on a centrifugal pump?
  • In what year does the Commissioner of Public Works present the annual report?
  • What is installed between two pipe flanges to ensure a sealed connection?
  • The type of motor that MOST frequently does NOT use brushes is the:
  • In plumbing, what technique involves using a rod for cleaning pipes?
  • What is a notable disadvantage of sludge lagoons in sewage treatment?
  • If you are pumping water at 100 gallons per minute for one hour and then 50 gallons per minute afterward, how long will it take to add 10,000 gallons to a tank?
  • Which is an important consideration in the operation of sludge digesters?
  • Which knot is safely used for tying the ends of two dry ropes of the same size?
  • Which type of pump seldom requires a relief valve?
  • What is the main purpose of a foot valve in a centrifugal pump?
  • What is a likely outcome for a person exposed to an irritant gas who does not become sick immediately?
  • How can the current in a simple electrical circuit be calculated?
  • The capacity of a pump is most frequently expressed in which of the following units?
  • What type of pipe does Schedule 40 designation refer to?
  • A pipe is generally threaded by using a:
  • A job requires 48 hours of work. If two workers are assigned to the job, how many hours will each worker need to work?
  • What tool is used for cutting internal screw threads?
  • The enlarged tank will be able to hold ____________ more than the original tank.
  • A regulator gate usually closes when the sewage reaches a predetermined:
  • Why is it important to monitor the effluent quality from a sewage treatment plant?
  • What does the word bearing mean in the article?
  • Which tool is most appropriate for threading a round rod?
  • What hazard is posed by hydrogen given off from charging batteries?
  • How many pounds are in ten bags of Portland cement?
  • When lifting heavy objects, how should one position their body?
  • Which of the following devices is usually operated by compressed air?
  • In the event of lye splashing into someone's eyes, what is the first recommended action?
  • In case of severe burns, what is the first thing you should do?
  • Which fraction is equivalent to 0.0625?
  • If a person is bleeding heavily, which is the most effective initial treatment?
  • The floating cover for a sludge gas storage tank is kept under a gauge pressure of?
  • What should be ensured about the cord of an electric hand tool during transportation?
  • Which of the following processes is utilized for nutrient removal in advanced sewage treatment?
  • What device in sewage treatment plants is designed to break or cut up solids found in sewage?
  • What is the total of 25% + 35% + 20% + 20%?
  • If a given saw has 8 points per inch, what type of saw is it likely to be?
  • How can a chlorine leak typically be detected?
  • What is a critical factor in the efficient operation of machinery?
  • What is the approximate amount of chlorine in pounds per million gallons to achieve 0.5 ppm residual in primary effluents?
  • What are short pieces of pipe threaded on both ends called?
  • Which action is least likely to promote good work by a leader?
  • Why is it best to use a screwdriver with a square shank?
  • If a seller quotes a discount of 10% on paint priced at $6.35 per gallon, what is the actual payment per gallon?
  • How often should routine maintenance of sewage treatment equipment typically occur?
  • What does the term atmosphere refer to in the context of the article?
  • The type of pipe that is MOST frequently made with bell and spigot ends is:
  • What is the most effective way for a supervisor to lower accident rates among workers?
  • What was the amount of municipal construction underway in 2012?
  • What is the resistance of the circuit if the voltage is 120 volts and the current is 2 amperes?
  • How does one ensure proper alignment of machine parts during reassembly?
  • What is the primary purpose of aeration in sewage treatment?
  • Which type of pump provides a smooth continuous flow of liquid?
  • What is the meaning of the word vacuum as used in the article?
  • What is the most important safety precaution when using an electric drill press?
  • In the electrical industry, what does BX refer to?
  • What does the term malodorous most closely mean?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy